Skip to main content
Electrical Engineering

Questions tagged [labview]

Ask Question

The tag has no summary.

35 questions
Newest Active Bountied Unanswered
0 votes
1 answer
52 views

I had small issue I can't understand how to overcome. I'm using psoc 5lp and wrote a code with uart that just work as ping pong, testing uart options for bigger project. So the psoc code works ...
ronen lipavsky's user avatar
  • 1
0 votes
0 answers
36 views

I'm working on a Labview application and facing a challenge with managing dependencies between UI elements in a clean and scalable way. Here's a breakdown of my issue: I have a Main VI with several ...
Mohammad Reza Hasanpour's user avatar
  • 77
4 votes
1 answer
66 views

I have a PSU that has no power controls, I can only set the current limit and the voltage limit, and I need to control a resistive load such that the rate of change of the power is limited to a set ...
Timothy Hennesy's user avatar
  • 41
0 votes
1 answer
229 views

When receiving data via SPI communication, is there any constraints for word length (bit size)? I have a chip that sends 16 bits of data A and 16 bits of data B through a single pin, can I configure ...
aglakd's user avatar
  • 5
3 votes
0 answers
147 views

From https://www.studyforfe.com/blog/steps-for-solving-the-two-method-wattmeter-problem/ : $$\begin{aligned} W_1 &= V_L \cdot I_L \cdot \cos(30°+\phi) \\ W_2 &= V_L \cdot I_L \cdot \cos(...
Fuergrissa72's user avatar
  • 31
0 votes
0 answers
56 views

I tried to understand what "Frequency range vi" consists. But I didn't understand. From Reference Article(doi:10.15199/48.2021.11.10): No.1 shows the block diagrams of fixed-point data ...
bahadir3301's user avatar
  • 17
0 votes
0 answers
111 views

Can you give an advice how to improve this? I want to combine a VNA with an Arduino in an RF anechoic chamber. The position contol will be performed by the Arduino. Reference article
bahadir3301's user avatar
  • 17
1 vote
1 answer
71 views

I am an absolute beginner about Labview. I don't want to stop in Tutorial Hell. That's why I try to pick it up by reading the project Labview Based Automatic Antenna Pattern Measurement and Gain ...
bahadir3301's user avatar
  • 17
0 votes
1 answer
80 views

I saw a symbol, what there is vertical double line inside triangle shape, on Labview 8.0. Is it "or" function? I also asked in Labview Community.
bahadir3301's user avatar
  • 17
0 votes
0 answers
101 views

I'm trying to measure the speed of a small DC motor using a rotary encoder and an OPTO sensor, and counter input on myDAQ. Here's my circuit on the breadboard: The collector pin of the transistor is ...
Charbel Nicolas's user avatar
  • 1
1 vote
1 answer
80 views

https://www.mediafire.com/file/30bw1s5uw8fexu6/VTOL+help.pdf/file From above link, I was reading a manual about QNET VTOL (Vertical Take off and Landing) trainer and I came across a the task/question ...
DSP_CS's user avatar
  • 1,181
0 votes
0 answers
661 views

I've got a system that uses two parameters, let's call them F and P, to control the mass flow rate of a substance flowing into a chamber. I need to control the concentration (grams per cubic meter) of ...
Ben S.'s user avatar
  • 79
1 vote
0 answers
123 views

I want to import a DLL to Labview and create VIs from my functions. For simple functions with common data types, it works well. My problem is when the function has a struct data type. I followed ...
Arcaniaco's user avatar
  • 161
0 votes
3 answers
1k views

my name is Joe Vaccarella. I am a research assistant at the University of Rochester. I’m currently conducting a project where I have 4 strain gages, mounted on a polycarbonate tube. (one gage on each ...
Joe Vaccarella's user avatar
  • 1
0 votes
1 answer
935 views

I have connected the circuit as shown. The circuit works perfectly when I Use the Arduino ide. When I use LabVIEW, the distance from the ultrasonic sensor is always zero. The LabVIEW circuit diagram ...
Alex Mwaura's user avatar
  • 31

15 30 50 per page
1
2 3